MCQ Questions Electrical Engineering D.C. Motors

DC Motors-2

MCQ Questions Electrical Engineering D.C. Motors

Take a look at these MCQ Questions Electrical Engineering D.C. Motors for engineering interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Electrical Engineering D.C. Motors
 

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering superhero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates.

The best engineering interview questions to ask candidates should be questions that reveal they have the skills required for the job. If you need a problem solver, ask questions about past experiences. If they need to have a specific skill set, ask them directly about their skills. This chapter consisting Electrical engineering MCQ Questions Electrical Engineering D.C. Motors

There are six major branches of engineering which include Electrical, Mechanical, Civil, Management, Geotechnical, and Chemical with many different subcategories under each main branch of engineering such as Structural or Biomedical engineering.

This article will get into the top engineering interview questions to ask candidates, eight types of interview questions, how to choose the questions you ask, and then will list excellent questions you can choose from. Let’s jump right in.

You can practice interviews using the resources available from our partners. MCQ Questions Electrical Engineering D.C. Motors are given below.

MCQ Questions Electrical Engineering D.C. Motors - Set - 2

Question 1: 

What will happen if the back e.m.f. of a D.C. motor vanishes suddenly?
(a) The motor will stop
(b) The motor will continue to run
(c) The armature may burn.
(d) The motor will run noisy

Correct Answer – (C)

Question 2 : 

In a D.C. shunt motor, speed is
(a) independent of armature current
(b) directly proportional to the armature current
(c) proportional to the square of the current
(d) inversely proportional to the armature current

Correct Answer – (A)

Question 3 : 

When two D.C. series motors are connected in parallel, the resultant speed is
(a) more than the normal speed
(b) loss than the normal speed
(c) normal speed
(d) zero

Correct Answer – (C)

Question 4 : 

If a D.C. motor is connected across the A.C. supply it will
(a) run at normal speed
(b) not run
(c) run at lower speed
(d) burn due to heat produced in the field winding by .eddy currents

Correct Answer – (D)

Question 5 : 

For starting a D.C. motor a starter is required because
(a) it limits the speed of the motor
(b) it limits the starting current to a safe value
(c) it starts the motor
(d) none of the above

Correct Answer – (B)

MCQ Questions Electrical Engineering D.C. Motors

Question 6: 

A direct on line starter is used: for starting motors
(a) up to 5 H.P.
(b) up to 10 H.P.
(c) up to 15 H.P.
(d) up to 20 H.P.

Correct Answer – (A)

Question 7: 

The speed of a D.C. shunt motor more than its full-load speed can be obtained by
(a) decreasing the field current
(b) increasing the field current
(c) decreasing the armature current
(d) increasing the armature current

Correct Answer – (A)

Question 8: 

To get the speed of D.C, motor below the normal without wastage of electrical energy is used.
(a) Ward Leonard control
(b) rheostatic control
(c) any of the above method
(d) none of the above method

Correct Answer – (A)

Question 9: 

The type of D.C. motor used for shears and punches is
(a) shunt motor
(b) series motor
(c) differential compoutid D.C. motor
(d) cumulative compound D.C. motor

Correct Answer – (D)

Question 10: 

A D.C. series motor is that which
(a) has its field winding consisting of thick wire and less turns
(b) has a poor torque
(c) can be started easily without load
(d) has almost constant speed

Correct Answer – (A)

MCQ Questions Electrical Engineering D.C. Motors

MCQ Questions Electrical Engineering D.C. Generators

Multiple Choice Questions for Competitive Exams