MCQ Questions Electrical Engineering Generation of Electrical Power

Electrical Engineering Generation of Electrical Power-3

MCQ Questions Electrical Engineering Generation of Electrical Power

Take a look at these MCQ Questions Electrical Engineering Generation of Electrical Power for engineering interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Electrical Engineering Generation of Electrical Power
 

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering superhero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates.

The best engineering interview questions to ask candidates should be questions that reveal they have the skills required for the job. If you need a problem solver, ask questions about past experiences. If they need to have a specific skill set, ask them directly about their skills. This chapter consisting Electrical engineering MCQ Questions Electrical Engineering Generation of Electrical Power

There are six major branches of engineering which include Electrical, Mechanical, Civil, Management, Geotechnical, and Chemical with many different subcategories under each main branch of engineering such as Structural or Biomedical engineering.

This article will get into the top engineering interview questions to ask candidates, eight types of interview questions, how to choose the questions you ask, and then will list excellent questions you can choose from. Let’s jump right in.

You can practice interviews using the resources available from our partners. MCQ Questions Electrical Engineering Generation of Electrical Power are given below.

MCQ Questions Electrical Engineering Generation of Electrical Power - Set - 3

Question 1: 

The draught produced by steel chimney as compared to that produced by brick chimney for the same height is

(a) less
(b) more
(c) same
(d) may be more or less

Correct Answer – (B)

Question 2 : 

The modern steam turbines are

(a) impulse turbines
(b) reaction turbines
(c) impulse-reaction turbines
(d) none of the above

Correct Answer – (C)

Question 3 : 

A steam power station requires space
(a) equal to diesel power station
(b) more than diesel power station
(c) less than diesel power station
(d) All of them

Correct Answer – (B)

Question 4 : 

Mercury is a choice with steam in binary vapour cycle because it has


(a) higher critical temperature and pressure
(b) higher saturation temperature than other fluids
(c) relatively low vapourisation pressure
(d) all above

Correct Answer – (D)

Question 5 : 

In regenerative cycle feed water is heated by

(a) exhaust gases
(b) heaters
(c) draining steam from the turbine
(d) all above

Correct Answer – (C)

MCQ Questions Electrical Engineering Generation of Electrical Power

Question 6: 

The draught which a chimney produces is called

(a) induced draught
(b) natural draught
(c) forced draught
(d) balanced draught

Correct Answer – (B)

Question 7: 

Economiser is used to heat

(a) air
(b) feed water
(c) flue gases
(d) all above

Correct Answer – (B)

Question 8: 

Binary’vapour cycles are used to

(a) increase the performance of the condenser
(b) increase the efficiency of the plant
(c) increase efficiency of the turbine

(d) None of them

Correct Answer – (B)

Question 9: 

Reheat cycle in steam power plant is used to


(a) utilise heat of flue gases

(b) increase thermal efficiency
(c) improve condenser performance
(d) reduce loss of heat

Correct Answer – (B)

Question 10: 

The maximum percentage gain in Regenerative feed heating cycle thermal efficiency

(a) increases with number of feed heaters increasing
(b) decreases with number of feed heaters increasing
(c) remains same unaffected by number of feed heaters
(d) none of the above

Correct Answer – (A)

MCQ Questions Electrical Engineering Generation of Electrical Power

MCQ Questions Electrical Engineering Rectifiers And Convertors

Multiple Choice Questions for Competitive Exams