MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures

Take a look at these MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures - Set - 4

Question 1:

Minimum grade of concrete to be used in reinforced concrete as per IS:456-1978 is
a) M15
b) M20
c) M 10
d) M25

Check Answer

Correct Answer – (A)

Question 2 :

If the permissible stress in steel in tension is 140 N/mm2, then the depth of neutral axis for a singly reinforced rectangular balanced section will be
a) 0.35 d
b) 0.40 d
c) 0.45 d
d) dependent on grade of concrete also

Check Answer

Correct Answer – (B)

Question 3 :

If the depth of actual neutral axis in a beam is more than the depth of critical neutral axis, then the beam is called
a) balanced beam
b) under-reinforced beam
c) over-reinforced beam
d) none of the above

Check Answer

Correct Answer – (C)

Question 4 :

If a beam fails in bond, then its bond strength can be increased most economi-cally by
a) increasing the depth of beam
b) using thinner bars but more in number
c) using thicker bars but less in number
d) providing vertical stirrups

Check Answer

Correct Answer – (B)

Question 5 :

For a reinforced concrete section, the shape of shear stress diagram is
a) wholly parabolic
b) wholly rectangular
c) parabolic above neutral axis and rectangular below neutral axis
d) rectangular above neutral axis and parabolic below neutral axis

Check Answer

Correct Answer – (C)

MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures

Question 6:

Modulus of elasticity of steel as per IS : 456-1978 shall be taken as
a) 20 kN/cm²
b) 200 kN/cm²
c) 200kN/mm²
d) 2xl06N/cm²

Check Answer

Correct Answer – (C)

Question 7:

If the depth of neutral axis for a singly reinforced rectangular section is represented by kd in working stress design, then the value of k for balanced section
a) depends on as, only
b) depends on aCbC only
c) depends on both crest and acbc
d) is independent of both ast and acbc where d is the effective depth, ast is permissible stress in steel in tension and ocbc is permissible stress in concrete in bending compression.

Check Answer

Correct Answer – (A)

Question 8:

If nominal shear stress tv exceeds the design shear strength of concrete xc, the nominal shear reinforcement as per IS : 456-1978 shall be provided for carrying a shear stress equal to
a) xv
b) xc
c) xv – TC
d) Tv + Tc

Check Answer

Correct Answer – (C)

Question 9:

Diagonal tension in a beam
a) is maximum at neutral axis
b) decreases below the neutral axis and increases above the neutral axis
c) increases below the neutral axis and decreases above the neutral axis
d) remains same

Check Answer

Correct Answer – (C)

Question 10:

Examine the following statements :
i) Factor of safety for steel should be based on its yield stress,
ii) Factor of safety for steel should be based on its ultimate stress,
iii) Factor of safety for concrete should be based on its yield stress,
iv) Factor of safety for concrete should be based on its ultimate stress.
The correct statements are
a) (i) and (iii)
b) (i)and(iv)
c) (ii) and (iii)
d) (ii) and (iv)

Check Answer

Correct Answer – (B)

MCQ Questions Civil Engineering Concrete Technology and Design of Concrete Structures

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Civil Engineering Design of Steel Structures

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5