MCQ Questions Civil Engineering Design of Steel Structures

Take a look at these MCQ Questions Civil Engineering Design of Steel Structures interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering Design of Steel Structures.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering Design of Steel Structures - Set - 2

Question 1:

For a standard 45° fillet, the ratio of size of fillet to throat thickness is
a) 1:1
b) 1 : V²
c) V² : 1
d) 2: 1

Check Answer

Correct Answer – (C)

Question 2 :

In the cross-section of a weld, throat is the
a) minimum dimension
b) average dimension
c) maximum dimension
d) none of the above

Check Answer

Correct Answer – (A)

Question 3 :

Diameter of a bolt hole is usually taken as
a) gross diameter of bolt
b) nominal diameter + 1.5 mm
c) nominal diameter + 2.0 mm
d) nominal diameter of bolt

Check Answer

Correct Answer – (B)

Question 4 :

Select the correct statement
a) Material cost of a rivet is higher than that of a bolt.
b) Tensile strength of a bolt is lesser than that of a rivet.
c) Bolts are used as a temporary fastenings whereas rivets are used as permanent fastenings.
d) Riveting is less noisy than bolting.

Check Answer

Correct Answer – (C)

Question 5 :

Minimum pitch of the rivets shall not be less than
a) 1.5 d
b) 2.0 d
c) 2.5 d
d) 3.0 d
where d is gross diameter of rivet

Check Answer

Correct Answer – (C)

MCQ Questions Civil Engineering Design of Steel Structures

Question 6:

The effective length of a fillet weld should not be less than
a) two times the weld size
b) four times the weld size
c) six times the weld size
d) weld size

Check Answer

Correct Answer – (B)

Question 7:

When the bolts are subjected to reversal of stresses, the most suitable type of bolt is
a) black bolt
b) ordinary unfinished bolt
c) turned and fitted bolt
d) high strength bolt

Check Answer

Correct Answer – (D)

Question 8:

Bolts are most suitable to carry
a) axial tension
b) bending
c) shear
d) shear and bending

Check Answer

Correct Answer – (A)

Question 9:

Efficiency of a riveted joint, having the minimum pitch as per IS : 800, is
a) 40%
b) 50%
c) 60%
d) 70%

Check Answer

Correct Answer – (C)

Question 10:

By providing sufficient edge distance, which of the following failures of riveted joint can be avoided ?
a) tension failure of the plate
b) shear failure of the rivet
c) shear failure of the plate
d) crushing failure of the rivet

Check Answer

Correct Answer – (C)

MCQ Questions Civil Engineering Design of Steel Structures

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Civil Engineering Structural Analysis

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5