MCQ Questions Civil Engineering RCC Structures Design

Take a look at these MCQ Questions Civil Engineering RCC Structures Design interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering RCC Structures Design.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering RCC Structures Design - Set - 1

Question 1:

In case the factor of safety against sliding is less than 1.5, a portion of slab is constructed downwards at the end of the heel slab, which is known as

A. A key
B. A cut-off wall
C. A rib
D. All the above

Check Answer

Correct Answer – (D)

Question 2 :

The floor slab of a building is supported on reinforced cement floor beams. The ratio of the end and intermediate spans is kept

A. 0.7
B. 0.8
C. 0.9
D. 0.6

Check Answer

Correct Answer – (C)

Question 3 :

The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is

A. 35
B. 25
C. 30
D. 20

Check Answer

Correct Answer – (C)

Question 4 :

The column head support a flat slab, is generally kept The diameter of
A. 0.25 times the span length
B. 0.25 times the diameter of the column
C. 4.0 cm larger than the diameter of the column
D. 5.0 cm larger than the diameter of the column

Check Answer

Correct Answer – (A)

Question 5 :

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is

A. Half of the width of the slab
B. Two -third of the width of the slab
C. Three-fourth of the width of the slab
D. Four-fifth of the width of the slab

Check Answer

Correct Answer – (C)

MCQ Questions Civil Engineering RCC Structures Design

Question 6:

Pick up the correct statement from the following:

A. Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling
B. Lateral reinforcement prevents the shearing of concrete on diagonal plane
C. Lateral reinforcement stops breaking away of concrete cover, due to buckling
D. All the above

Check Answer

Correct Answer – (D)

Question 7:

If the width of the foundation for two equal columns is restricted, the shape of the footing generally adopted, is

A. Square
B. Rectangular
C. Trapezoidal
D. Triangular

Check Answer

Correct Answer – (B)

Question 8:

Fixed at its ends, the If is the uniformly distributed load on a circular slab of radius maximum positive radial moment at its centre, is
A. 3WR²/16
B. 2WR²/16
C. WR²/16
D. None of these

Check Answer

Correct Answer – (C)

Question 9:

The load stress of a section can be reduced by

A. Decreasing the lever arm
B. Increasing the total perimeter of bars
C. Replacing larger bars by greater number of small bars
D. Replacing smaller bars by greater number of greater bars

Check Answer

Correct Answer – (C)

Question 10:

An R.C.C. beam of 6 m span is 30 cm wide and has a lever arm of 55 cm. If it carries a U.D.L. of 12 t per m and allowable shear stress is 5 kg/cm2, the beam

A. Is safe in shear
B. Is safe with stirrups
C. Is safe with stirrups and inclined bars
D. Needs revision of section

Check Answer

Correct Answer – (D)

MCQ Questions Civil Engineering RCC Structures Design

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Civil Engineering Waste Water Engineering

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5