MCQ Questions Civil Engineering RCC Structures Design

Take a look at these MCQ Questions Civil Engineering RCC Structures Design interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering RCC Structures Design.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering RCC Structures Design - Set - 4

Question 1:

The neutral axis of a T-beam exists

A. Within the flange

B. At the bottom edge of the slab

C. Below the slab

D. All the above

Check Answer

Correct Answer – (D)

Question 2:

A pre-cast pile generally used, is

A. Circular

B. Square

C. Octagonal

D. Square with corners chamfered

Check Answer

Correct Answer – (D)

Question 3:

The spacing of transverse reinforcement of column is decided by the following consideration.

A. The least lateral dimension of the column

B. Sixteen times the diameter of the smallest longitudinal reinforcing rods in the column

C. Forty-eight times the diameter of transverse reinforcement

D. All the above

Check Answer

Correct Answer – (D)

Question 4:

The self-weight of the footing, is

A. Not considered for calculating the upward pressure on footing

B. Also considered for calculating the upward pressure on footing

C. Not considered for calculating the area of the footing

D. Both B. and C.

Check Answer

Correct Answer – (A)

Question 5:

Pick up the incorrect statement from the following:

A. In the stem of a retaining wall, reinforcement is provided near the earth side

B. In the toe slab of a retaining wall, reinforcement is provided at the bottom of the slab

C. In the heel slab of a retaining wall, reinforcement is provided at the top of the slab

D. None of these

Check Answer

Correct Answer – (D)

MCQ Questions Civil Engineering RCC Structures Design

Question 6:

An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus

A. Triangular load of the wall

B. UDL of wall

C. UDL of wall + load from the roof

D. Triangular load + load from the roof

Check Answer

Correct Answer – (C)

Question 7:

The minimum clear cover for R.C.C. columns shall be

A. Greater of 40 mm or diameter

B. Smaller of 40 mm or diameter

C. Greater of 25 mm or diameter

D. Smaller of 25 mm or diameter

Check Answer

Correct Answer – (C)

Question 8:

The minimum thickness of a flat slab is taken

A. L/32 for end panels without drops

B. L/36 for end panels without drops

C. L/36 for interior panels without drop

D. All the above

Check Answer

Correct Answer – (D)

Question 9:

The design of heel slab of a retaining wall is based on the maximum bending moment due to:

A. Its own weight

B. Weight of the soil above it

C. Load of the surcharge, if any

D. All the above

Check Answer

Correct Answer – (D)

Question 10:

An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is

A. Safe in shear

B. Is safe with stirrups

C. Is safe with stirrups and inclined members

D. Needs revision of the section

Check Answer

Correct Answer – (A)

MCQ Questions Civil Engineering RCC Structures Design

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Civil Engineering Waste Water Engineering

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5