MCQ Questions Civil Engineering RCC Structures Design

Take a look at these MCQ Questions Civil Engineering RCC Structures Design interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering RCC Structures Design.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering RCC Structures Design - Set - 5

Question 1:

The pitch of the main bars in a simply supported slab, should not exceed its effective depth by

A. Three times

B. Four times

C. Five times

D. Six times

Check Answer

Correct Answer – (D)

Question 2:

High strength concrete is used in pre-stressed member

A. To overcome high bearing stresses developed at the ends

B. To overcome bursting stresses at the ends

C. To provide high bond stresses

D. All the above

Check Answer

Correct Answer – (D)

Question 3:

On a circular slab of radius , the maximum radial moment at the centre of the If is the load slab, is WR²/16
A. WR²/16
B. 2WR²/16
C. 3WR²/16
D. 5WR²/16

Check Answer

Correct Answer – (C)

Question 4:

If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is

A. 0.496 %

B. 0.596 %

C. 0.696 %

D. 0.796 %

Check Answer

Correct Answer – (C)

Question 5:

The modular ratio m of a concrete whose permissible compressive stress is C, may be obtained from the equation.

A. m = 700/3C

B. m = 1400/3C

C. m = 2800/3C

D. m = 3500/3C

Check Answer

Correct Answer – (C)

MCQ Questions Civil Engineering RCC Structures Design

Question 6:

If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is

A. D = 0.0775 a

B. D = 0.775 a

C. D = 0.775 a

D. D = 0.775 a2

Check Answer

Correct Answer – (A)

Question 7:

After pre-stressing process is completed, a loss of stress is due to

A. Shrinkage of concrete

B. Elastic shortening of concrete

C. Creep of concrete

D. All the above

Check Answer

Correct Answer – (D)

Question 8:

In a simply supported slab, alternate bars are curtailed at

A. 1/4th of the span

B. 1/5th of the span

C. 1/6th of the span

D. 1/7th of the span

Check Answer

Correct Answer – (D)

Question 9:

In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2, nominal reinforcement is provided at a pitch of

A. One -half lever arm of the section

B. One-third lever arm of the section

C. Lever arm of the section

D. One and half lever arm of the section

Check Answer

Correct Answer – (C)

Question 10:

The transverse reinforcements provided at right angles to the main reinforcement

A. Distribute the load

B. Resist the temperature stresses

C. Resist the shrinkage stress

D. All the above

Check Answer

Correct Answer – (D)

MCQ Questions Civil Engineering RCC Structures Design

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Civil Engineering Waste Water Engineering

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5