MCQ Questions Civil Engineering Surveying

Take a look at these MCQ Questions Civil Engineering Surveying interview questions and our tips on how to answer them. If you’re applying for an engineering internship, graduate scheme or entry-level job, you’ll face at least one interview as part of an engineering employer’s recruitment process. You may be interviewed by one or more members of the HR team, senior members of the engineering team you’d be joining or a mixture of both. In this section we will study MCQ Questions Civil Engineering Surveying.

As well as questions about your reasons for applying to the role and the employer in question, engineering recruiters will be assessing your potential in the areas that is crucial to any engineering role: technical expertise. Engineers may be asked to perform feats of fantastic technical prowess, but it will be as as part of a Justice League rather than as a solo engineering super hero.

The interviewer is almost as nervous as the candidate in most interviews. You might wonder if you look confident enough, if you will hire the right person, or if you are asking the right engineering interview questions. The last question is arguably the most crucial part to worry about when you’re interviewing candidates. Other topics on Civil Engineering Multiple Choice Questions can be accessed

MCQ Questions Civil Engineering Surveying - Set - 2

Question 1:

For a line AB
a) the forebearing of AB and back bearing of AB differ by 180°
b) the forebearing of AB and back bearing of BA differ by 180°
c) both (a) and (b) are correct.
d) none is correct

Check Answer

Correct Answer – (A)

Question 2 :

If the true bearing of a line AB is 269° 30′, then the azimuth of the line AB is
a) 0° 30′
b) 89° 30′
c) 90° 30′
d) 269° 30′

Check Answer

Correct Answer – (C)

Question 3 :

The length of a chain is measured from
a) centre of one handle to centre of other handle
b) outside of one handle to outside of other handle
c) outside of one handle to inside of other handle
d) inside of one handle to inside of other handle

Check Answer

Correct Answer – (B)

Question 4 :

The maximum tolerance in a 20 m chain is
a) ±2 mm
b) ±3 mm
c) ±5 mm
d) ±8 mm

Check Answer

Correct Answer – (C)

Question 5 :

Which of the following is not used in measuring perpendicular offsets ?
a) line ranger
b) steel tape
c) optical square
d) cross staff

Check Answer

Correct Answer – (A)

MCQ Questions Civil Engineering Surveying

Question 6:

In the prismatic compass
a) the magnetic needle moves with the box
b) the line of the sight does not move with the box
c) the magnetic needle and graduated circle do not move with the box
d) the graduated circle is fixed to the box and the magnetic needle always remains in the N-S direction

Check Answer

Correct Answer – (C)

Question 7:

elect the incorrect statement.
a) The true meridians at different places are parallel to each other.
b) The true meridian at any place is not variable.
c) The true meridians converge to a point in northern and southern hemispheres.
d) The maps prepared by national survey departments of any country are based on true meridians.

Check Answer

Correct Answer – (A)

Question 8:

For accurate work, the steel band should always be used in preference to chain because the steel band
a) is lighter than chain
b) is easier to handle
c) is practically inextensible and is not liable to kinks when in use
d) can be easily repaired in the field

Check Answer

Correct Answer – (C)

Question 9:

If the length of a chain is found to be short on testing, it can be adjusted by
a) straightening the links
b) removing one or more small circular rings
c) closing the joints of the rings if opened out
d) all of the above

Check Answer

Correct Answer – (A)

Question 10:

Normal tension is that pull which
a) is used at the time of standardising the tape
b) neutralizes the effect due to pull and sag
c) makes the correction due to sag equal to zero
d) makes the correction due to pull equal to zero

Check Answer

Correct Answer – (B)

MCQ Questions Civil Engineering Surveying

NCERT Solutions & Download NCERT Textbooks

MCQ Questions Mechanical Engineering Mechanics

Multiple Choice Questions for Competitive Exams

Multiple Choice Questions Class 12 Chemistry The Solid State

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Solutions With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Electrochemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Chemical Kinetics With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 Surface Chemistry With Answers

Set -1 Set -2 Set -3 Set -4 Set -5
MCQ Questions Class 12 General Principles and Processes of Isolation of Elements With Answers

Set -1 Set -2 Set -3 Set -4 Set -5